Eternit SYSTEMFLOOR™ is an innovative new light-weight flooring system which is easy and fast to install.
Eternit SYSTEMFLOOR™ is manufactured to meet environmental standards.
- Lightweight yet strong and resistant
- Rapid to install
- Lapped joint fixing board to board
- Termite resistant
|Eternit SYSTEMFLOOR™ Dimensions|
(mm x mm)
(mm x mm)
|Total board weight
|18||650 x 2700||600 x 270||20||32|
|18||1250 x 2700||1200 x 2700||20||64|
|18||1200 x 2400||1200 x 2400||20||57|
*Other dimensions are available upon request. The properties in above tables are mean values given for information and guidance only. If certain properties are critical for a particular application, it is advisable to consult Eternit.
Eternit SYSTEMFLOOR™ Cement Bound Matrix board is manufactured under a quality management system certified in accordance with ISO 9001: 2008.
|Flexural strength, Frupture
(BS EN 310: 1993)
|Tensile strength, Trupture
(BS5669: Part 1: 1989)
(average, perpendicular on board face)
(BS 5669: Part 1: 1989)
Physical and mechanical properties
|General Technical Properties|
|Product generic description||Cement Bound Matrix board|
|Non Combustible||EN ISO 1182: 2002
BS 476: Part 4
|Building regulations classification||Class 0 (BS 476: Parts 6 & 7)|
|Heat and smoke release rates (tested to AS/NZS 3837)||Group 1|
|Spread of flame for bare floors (tested to AS ISO 9239: Part 1)||Passed|
|Thermal conductivity (approximate) at 20°C||W/m°K||0.166|
|Simultaneous determination of ignitability, flame propagation, heat
and smoke release
(tested to AS 1530: Part 3)
|Determination of ignitability: 0
Determination of flame propagation: 0
Determination of heat release: 0
Determination of smoke developed: 0-1
|Water permeability (tested to AS 2908: Part 2: 2000)||Passed|
|Water proof (tested to AS 3740: 2004 using wet area membrane)||Impermeable to water|
|Water Tightness to BS 4624: 1981||Passed|
|Alkalinity (approximate)||pH||9 – 10|
|Typical moisture content
(ambient to dry condition, tested to BS 5669: Part 1, Clause 9)
|Uniformly Distributed Loads
(in accordance with AS/NZS 1170: Part 1 up to 20kPa)
|Concentrated loads on joists spaced at 450mm centres
(single layer of board 18mm thick)
In accordance with AS/NZS 1170.0
Using 0.01m² diameter applicator kN
Using 350mm² applicator (punch test)
|Maximum concentrated load
(no visible growth of Mildew in accordance with HN 0028)
|Acoustic (One hour fire resistant floor system)
|Rw +Ctr 52
LnW + Ci 56
Complying with most residential requirements.
|Density (tested to BS 5669: Part 1: 1989, Clause 8)||kg/m³||Nominal 1100|
|Emission test (to ASTM D5116-90 for Green Label Singapore)||Within limits set out by the Singapore Environment Council|
|Steel and timber joists centres||450mm centres|
|Thickness tolerance of standard boards||mm||± 0.5 for board thickness ≤ 15
± 1.0 for board thickness > 15
|Length x width tolerance of standard boards||mm||± 1|
|Surface condition||Smooth and fair face on both sides|
NOTE 1: Standards and codes may determine that higher loads may need to be considered. A registered structural engineer should be consulted in these instances.
NOTE 2: These tests satisfy the requirements for ultimate limit states.
NOTE 3: If a butt joint does not land on a joist, it shall be supported with a noggin of the same material as the main supports.
NOTE: Eternit SYSTEMFLOOR™ is not a finished product and should always have a floor covering applied to stop mechanical damage and an approved waterproofing system if used in areas where water is present.